< Previouswww.humboldtmfg.com • 1.800.544.7220 • 708.468.6300 238 CEMENT Cube Mold Testing H-2804 H-2817 H-2816.8 H-2860 H-2860W H-3855 H-2812 H-2809 H-2800 H-2805-R H-2805-A H-3272 Cube Mold, Stamped Construction 2" cube mold with diagonal arrangement. Used with cement, gypsum, lime, mortars, etc. These molds do not meet ASTM or AASHTO specifica- tions and must be individually measured. Cube Mold, Stamped ConstructionH-2809 Ship wt. 1.7lbs. (0.7kg) Briquette Mold ASTM C307 Cast-bronze briquette mold for hydraulic cement mortar tensile strength tests. Bronze clamps with pins hold the two mold halves securely. Designed to prevent spreading during molding. Briquette MoldH-2800 Ship wt. 3.5lbs. (1.5kg) Tamper, Oak ASTM C348 Tamper made of seasoned oak wood that has been Dipped in paraffin wax rendered Non absorptive. Tamper, OakH-3272 Ship wt. 0.3lbs. (0.14kg) Tamper, Wood ASTM C87, C109, C157, C185, C596; AASHTO T106, T137, T160 Wood tamper is 6" (152mm) long with 0.5 x 1" (13 x 25mm) cross section. Tamper, WoodH-2860W Ship wt. 0.3lbs. (0.14kg) Tamper, Rubber Compound Rubber compound tamper is 6" (152mm) long with 0.5 x 1" (13 x 25mm) cross section. Does not comply with ASTM standards. Tamper, Rubber CompoundH-2860 Ship wt. 0.3lbs. (0.14kg) Tamping Stick ASTM C185; AASHTO T137 Maple wood with .625" (16mm) dia. and 6" (152mm) length. Tamping StickH-3855 Ship wt. 0.1lbs. (0.04kg) Rubbing Block Ground steel block 3" dia. x 1" (76 x 25mm) for removing lose sand grains and encrusta- tions from concrete specimen surfaces before compressive testing. Rubbing BlockH-2812 Ship wt. 0.2lbs. (0.09kg) Digital Caliper, 0-200mm Provides accurate outside, inside, depth and step measurements and features large, easy-to-read LCD digits, rolling thumb wheel; plus control but- tons for zero, on/off and inch/mm functions. Digital Caliper, 0-200mmH-2816.8 Ship wt. 2.2lbs. (1kg) Dial Caliper, Stainless Steel 6" (150mm) Easy-to-read black face dial caliper with com- bination inch and metric scales features 0.001"/ 0.1mm graduations, hardened and ground stain- less steel main beam with hardened, ground and lapped measuring faces. Dial Caliper, Stainless Steel 6" (150mm)H-2817M Ship wt. 1.5lbs. (0.68kg) Dial Caliper, Stainless Steel 6" Similar to above, features a 6" measuring range with .001" graduations and .100" per revolution. Dial Caliper, Stainless Steel 6" (150mm)H-2817 Ship wt. 1.3lbs. (0.58kg) Certified Calipers are also available, please inquire. 2" Cube Compression Pad, Amber Compression pad, 85 durometer, used in com- pression tests of 2" cubes. Used with H-2804 Retainer Caps. Sold individually. 2" Cube Compression Pads, AmberH-2805-A Ship wt. .25lbs. (.11kg) 2" Cube Compression Pad, Red Compression pad, 70 durometer, used in com- pression tests of 2" cubes. Used with H-2804 Retainer Caps. Sold individually. 2" Cube Compression Pads, RedH-2805-R Ship wt. 0.25lbs. (0.11kg) 2" Cube Pad Retainer Caps Stainless steel retainer caps for use with 2" cube specimens. Use with 2" compression pads to eliminate the need for capping compound. Sold in sets of 2. 2" Cube Pad Retainer CapsH-2804 Ship wt. 0.25lbs. (0.23kg) 2" Cube Compression Pads Set Compression pads used with H-2804 Retainer Caps. Sold in set, consisting of (2) H-2805-R and (2) H-2805-A. 2" Cube Compression Pads SetH-2805 Ship wt. .5lbs. (.22kg)www.humboldtmfg.com • 1.800.544.7220 • 708.468.6300 CEMENT 239Prism Molds H-3251RC H-3257 H-3251 Prism Molds ASTM C490 Designed to produce required 10" effective gauge length, prism test bars. Molds feature removable partitions, base and end plates. Effective gauge length is measured from inside end of the studs. Molds produce cement prism specimens 11.25" long. Including studs, outside to outside length of specimen is 11.625". Prism Molds see chart Ship wt. see chart Gauge Studs ASTM C151, C157, C227, C490; AASHTO M210, T107. Gauge studs have stainless steel contact points and are knurled and threaded for use with cement prism molds. Packaged 10 per bag. Gauge Studs H-3260 Ship wt. 0.15lbs. (0.06kg) Tamping Rod ASTM C157, C192; AASHTO T60. Round, straight steel .375" dia. x 12" (10 x 305mm). Both ends rounded to a hemispherical tip the same diameter as the rod. Tamping Rod H-2905.1 Ship wt. 0.5lbs. (0.23kg) Restraining Cage, 2" x 2" x 10" ASTM C806 For 2" x 2" x 10" (51 x 51 x 254mm) prism molds. Features 1/4-20 continuous threaded rod and acorn nuts. Retaining Cage, 2" x 2" x 10" H-3251RC Ship wt. 1.4lbs. (0.63kg) Restraining Cage, 3" x 3" x 10" ASTM C878 For 3" x 3" x 10" (51 x 51 x 254mm) prism molds. Features 1/4-20 continuous threaded rod and acorn nuts. Restraining Cage, 3" x 3" x 10" H-3257 Ship wt. 2.8lbs. (1.27kg) Demold Device for Prism Molds Handy device for removing prism samples from molds. Demolding Device for Prism Molds H-3258DD Ship wt. 4lbs. (1.8kg) Go-No Go Gauge For gauge stud and molds. Dimensions: 1"x 1" x 10" molds. Go-No Go Gauge H-3258 Ship wt. 2lbs. (0.9kg) Prism Molds DescriptionShip wt.Model Application: Autoclave expansion of Port- land cement; length change of mortar and concrete; potential alkali reactivity of cement/ aggregate combinations; linear change of magnesium and oxychloride cements; volume change of cement paste 1" x 1" x 10" (25 x 25 x 254mm), 1-mold, cold-rolled steel 7.3 lbs (3.3kg) H-3252 1" x 1" x 10" (25 x 25 x 254mm), 2-mold, cold-rolled steel 9.6 lbs (4.3kg) H-3253 1" x 1" x 5" (25 x 25 x 127mm), 2-mold, stainless steel 6 lbs (2.72kg) H-3255S H-3260 H-3258DD DescriptionShip wt.Model Application: Volume change tests of mortars 2" x 2" x 10" (51 x 51 x 254mm), 2-mold, cold-rolled steel 20.6 lb (9.3kg) H-3251 1" x 1" x 5" (25 x 25 x 127mm), 2-mold, cold-rolled steel 6 lb (2.7kg) H-3255 Application: Volume change of cement past; length change of mortar and concrete 3" x 3" x 10" (76 x 76 x 254mm), 1-mold, cold-rolled steel 24.8 lbs (11kg) H-3254 Application: Volume change tests 4" x 4" x 10" (102 x 102 x 254mm), 1-mold, cold-rolled steel 35.5 lbs (16.1kg) H-3256 H-3255S H-3253 H-3252 H-3256 H-2905.1www.humboldtmfg.com • 1.800.544.7220 • 708.468.6300 240 CEMENT Vibrating Table, Expansion Vibrating Table, 3-gang Molds ASTM C109; EN 196-1 Required for compaction of 40 x 40 x 160 mm samples for EN 196-1 standard. It can be ordered with either a fast-action clamp fitting or a general-purpose clamp fitting for (1) 3-gang mold for 40 x 40 x 160mm samples. The vibrat- ing plate is 400 x 300 mm in size and is built into a powder-coated steel cabinet. The power switch box is mounted on a post attached to the top of the cabinet. Oscillation frequency is 50Hz with a sinusoidal waveform and digital timer. Peak-to-peak value is 0.75 ± 0.05mm. (Note: Order molds and Feeding Hoppers sepa- rately below. A total vibrating mass of 35.0 +/- 1.5 kg acc. to EN 196-1 can only be guaranteed by utilizing the precision three-gang mold with feeding hopper listed below. ) Vibrating Table w/ Fast-action Clamp, 230V 50/60Hz HC-3253.4F w/ General Clamp, 230V 50/60Hz HC-3254.4F w/ Cube Clamp, 230V 50/60Hz HC-3255.4F Ship wt. 552lbs. (250kg) Precision, 3-gang Mold EN 196-1 For use with vibrating table above. 40.1 x 40 x 160mm. Polished bright surface with numbered webs and nut plates. Electroless nickel finish. Precision, 3-gang MoldHC-3253.1 Ship wt. 22.5lbs. (10.2kg) 2" Cube, 3-gang Mold ASTM C109; AASHTO T106 Required for compaction of 2" (50mm) cubes samples for ASTM C109 standard. It can be ordered with a fast-action clamp fitting. Precision, 3-gang MoldHC-3253.3 Ship wt. 7.7lbs. (3.3kg) Feeding Hoppers for 3-gang Molds Feeding hopper for 3-gang mold. See Fast-Action and General Clamp photos above. Feeding Hopper, 3-gang Prism MoldHC-3253.2 Feeding Hopper, 3-gang Cube MoldHC-3253.4 Ship wt. 1.4lbs. (0.63kg) High-Pressure Autoclave ASTM C141, C151 Uses accelerated means of estimating delayed expansion of Portland cement caused by hydra- tion of CaO and MgO. This is done by determining the volume constancy of mortar prism samples. Test bars are exposed to high-pressure steam compartment, which accepts a sample holder for 8 prisms per ASTM, 1" x 1" x 11.25" (25 x 25 x 285mm) and 6 prisms as per the DIN standard, 40 x 40 x 160mm. Unit has a capacity of 7.8 liters, a max pressure of 360 psi (25 bar) and a max tem- perature of 482°F (250°C). Includes two gauges, one for temperature and one for pressure and a safety pop valve for safety. Also includes security test certificate for pressure chamber in accordance with EN pressure device directive. The 120V 60Hz version of this autoclave comes with an auxiliary voltage converter, which is included. Overall dimensions: 20.5 dia" x 44" (550 dia x 1120). High-Pressure Autoclave, 120V 60HzH-3241 High-Pressure Autoclave, 220V 50HzH-3241.5F Ship wt. 220lbs. (100kg) Prism Bar Frame ASTM C141, C151 Prism bar frame for use with H-3241 autoclave. ASTM model holds 8 prisms 1" x 1" x 11.25" (25 x 25 x 285mm). DIN model holds 6 prisms 40 x 40 x 160mm. Prism Bar Frame, ASTMH-3241.1 Prism Bar Frame, DINH-3241.2 Ship wt. 4lbs. (1.8kg) General Clamp* Fast-Action Clamp* HC-3253.1 HC-3253.3 *Shown with Feeding Hopper Feeding Hopper Cube Molds H-3241 H-3241.2 H-3241.1 HC-3254.4F HC-3255.4Fwww.humboldtmfg.com • 1.800.544.7220 • 708.468.6300 CEMENT 241Expansion H-3240 H-3240.22 H-3240.21M H-3240.21N H-3242 H-3240.4 H-3243BH-3243A Cement Autoclave ASTM C151; AASHTO T107 Uses accelerated means of estimating delayed expansion of Portland cement caused by hydra- tion of CaO and MgO. Test bars are exposed to controlled steam pressure and corresponding constant temperature. Unit produces 60-350 psi (0.4-2.4MPa) range of pressures and consists of steam vessel, pressure regulator, pressure gauge (0-600 psi x 5 psi), air vent valve, power switches and safety pop valve set at 350psi. Includes 20° 500°F spirit thermometer, wrench and 5 gaskets. Additional gaskets, heating units and safety pop valves are available as replacement parts. Cham- ber dimensions: 6.125" ID x 16". Overall dimen- sions: 17" x 48" x 28" (431 x 1219 x 711mm) 1700W maximum power demand. 220V version comes with transformer. Cement Autoclave, 120V 60HzH-3240 Cement Autoclave, 220V 50/60HzH-3240.4F Ship wt. 180lbs. (81.6kg) Rupture Disk Rupture disks are used as safety devices in sys- tems that involve pressure vessels, eliminating the need for a safety valve. The rupture disk is designed to be the weakest part of a pressure system so if there is a situation when excessive pressures occur, then the rupture disk fractures or opens thus releasing the built-up energy render- ing the system safe. Rupture disks are a simple, yet reliable method for providing a safe system, which does not require calibration. Both disks are rated to 420°F. The Monel disk is rated to 375psi and the Nickel disk is rated to 341psi. Rupture Disk, MonelH-3240.21M Rupture Disk, NickelH-3240.21N Ship wt. 0.4lbs. (0.18kg) Rupture Disk Holder Rupture disk holder, complete with piping to attach to the H-3240 cement autoclave. Order rupture disks separately. Rupture Disk HolderH-3240.22 Ship wt. 2.9lbs. (1.3kg) Test Bar Holder, 10" ASTM C141, C151; AASHTO T107 Test bar holder for 10"-long (254mm) gauge bars; 8-bar capacity. Holds specimens vertically, above water level, so each test bar is exposed to steam. Test Bar HolderH-3243B Ship wt. 2.9lbs. (1.4kg) Test Bar Holder, 5" ASTM C141, C151; AASHTO T107 Test bar holder for 5"-long (127mm) samples. Test Bar HolderH-3243A Ship wt. 4lbs. (1.8kg) Test Bar Holder Only ASTM C227 Test bar holder (stainless steel) for use with H-3267 mortar bar container. Holder supports six bars vertically and has feet that elevate it from the base of the container providing space for water. Test Bar Holder OnlyH-3267.ST Ship wt. 4lbs. (1.8kg) H-3267.ST DescriptionModel Air vent valve H-3240.2 Safety pop-off valve H-3240.3 Pressure gauge H-3240.4 Pressure-control switch H-3240.5 Set of cap screws, 16 per set H-3240.6 Relay 60Hz H-3240.7 Gaskets,100 per package H-3242 Lower heating unit for discon- tinued models. 115V. 50/60Hz H-3244 Heating element; two-piece wrap-around type for both top and bottom. 115V 50/60Hz H-3245 Thermometer, 20 to 580°F H-2600.2F Thermometer, -5 to 300°C H-2610.2C Autoclave Replacement Parts H-3240.3 For Prism Molds, please see page 239 ACCESSORIES H-3245 H-3244www.humboldtmfg.com • 1.800.544.7220 • 708.468.6300 242 CEMENT Expansion, Flow H-3265 H-3267B H-3267 Mortar Bar Container, Round with Bar Holder ASTM C227 Plastic container includes H-3267.ST Test bar holder (stamped-steel) that supports 6 bars verti- cally. Holder has feet that elevate it from the base of the container, which provides space for water and keeps test bars out of the water. Dimensions: 6" dia. x 17" (152 x 432mm). Mortar Bar Container with Bar HolderH-3267 Ship wt. 6.1lbs. (2.7kg) Test Bar Holder Only, Stamped Steel ASTM C227 Test bar holder (stamp steel) for use with H-3267 mortar bar container. Holder supports six bars vertically and has feet that elevate it from the base of the container providing space for water. Test Bar Holder OnlyH-3267.ST Ship wt. 4lbs. (1.8kg) Mortar Bar Container, Round with Bar Holder ASTM C227 Plastic container includes H-3267.1 Test bar holder (cast bronze) that supports 6 bars ver- tically. Holder has feet that elevate it from the base of the container, which provides space for water and keeps test bars out of the water. Dimensions: 6" dia. x 17" (152 x 432mm). Mortar Bar Container with Bar HolderH-3267B Ship wt. 6.1lbs. (2.7kg) Test Bar Holder Only, Cast Bronze ASTM C227 Test bar holder (cast bronze) for use with H-3257B mortar bar container. Holder has feet that elevate it from the base of the container providing space for water. Test Bar Holder OnlyH-3267.1 Ship wt. 4lbs. (1.8kg) Mortar Bar Container, 9" x 11" x 15.5" ASTM C227, C1260 Stainless steel covered container for storing test specimens has tight-fitting cover that prevents mois- ture loss. Supports up to 36 mortar bars vertically. Dimensions: 9" x 11" x 15.5" (229 x 279 x 394mm). Container, Mortar Bar-RectangularH-3265 Ship wt. 16lbs. (7.2kg) Flow Table, Motorized with Counter ASTM C87, C109, C110, C185, C230, C243, C348, C593; AASHTO T71, T106, T137 and T152 Used to determine the flow of hydraulic cement, mortars and cement pastes. A test specimen is molded on the table to a specified volume and shape. Then, with the mold removed, leaving the test specimen on the table. The table is dropped and raised (via a hand crank or optional motor) a specified number of cycles, after which the flow (or increase in average diameter of the specimen) is measured. Motorized flow table with 10" (254mm) dia. cast-bronze table/platen and automatic digital counter. Motor stops automatically once pre-set number of drops is achieved. Includes heavy-duty table/platen assembly, standard H-3622 cast bronze, 2.75" top dia. x 2" high x 4" bottom dia. cone mold, motor and H-3614B counter. Designed to be mounted to concrete mounting block. Order H-3624F, pedestal form and easily create your own mounting block. Appli- cations include: compression strength and air con- tent tests of cement mortar; flow tests of hydraulic cement mortars; consistency tests of magnesium oxychloride cements; flexural strength test for bond strength or mortar to masonry units. Flow Table, w/Counter, 120V 60HzH-3624 Flow Table, w/Counter, 220V 60HzH-3624.2F Flow Table, w/Counter, 220V 50HzH-3624.5F Ship wt. 81lbs. (37kg) Flow Table, Motorized ASTM C230 Used to determine the flow of hydraulic cement, mortars and cement pastes. A test specimen is molded on the table to a specified volume and shape. Then, with the mold removed, leaving the test specimen on the table. The table is dropped and raised (via a hand crank or optional motor) a specified number of cycles, after which the flow (or increase in average diameter of the specimen) is measured. Motorized flow table with 10" (254mm) dia. cast-bronze table/platen. Includes heavy-duty table/platen assembly, standard H-3622 cast bronze, 2.75" top dia. x 2" high x 4" bottom dia. cone mold, and motor. Designed to be mounted to concrete mounting block. Order H-3624F, ped- estal form and easily create your own mount- ing block. Used in determining consistency of cement mortars. Flow Table, Motorized, 120V 60HzH-3625 Flow Table, Motorized, 220V 60HzH-3625.2F Flow Table, Motorized, 220V 50HzH-3625.5F Ship wt. 80lbs. (36kg) Flow Table, Hand-Driven ASTM C230 Hand-driven flow table with 10" (254mm) dia. cast-bronze table/platen. Includes standard H-3622 cast bronze, 2.75" top dia. x 2" high x 4" bottom dia. cone mold. Used in determining con- sistency of cement mortars. Flow Table, Hand-DrivenH-3620 Ship wt. 27lbs. (12.2kg) 220V 60Hz machines require a transformer, which is included NOTES H-3620www.humboldtmfg.com • 1.800.544.7220 • 708.468.6300 CEMENT 243Flow Properties H-2833 H-2834SSB HC-2834S H-2834 H-2834.P Grout Flow Cone Set ASTM C939 These test sets are used to determine the time of efflux of a specified amount of fluid hydraulic cement grout, by allowing it to flow through a standardized flow cone. It can be used for with preplaced-aggregate (PA), but can also be used for other fluid grouts. The test method described in ASTM C939 determines the flowability by mea- suring the time of discharge of a 1.725L sample of grout as it is passed through a 0.5" (12.7mm) orifice at the bottom of the cone. Humboldt’s HC-2834S test set, which complies with ASTM C939, is comprised of a cast aluminum cone with a top ID of 7" (178mm) and a replaceable orifice at the bottom of 0.5" (12.7mm). The cone also includes an adjustable point gauge assem- bly, which is used to indicate the initial level of the grout sample. The set also includes a sturdy, tripod stand, which allows the cone to firmly fit into for testing (H-2833) and a 6L stainless steel beaker (H-2434SSB). The test set is also available with a 0.75" (19mm) orifice (HC-2835S), which does NOT comply with ASTM C939, but accom- modates grout with larger aggregate. All items of the set are available as individual items, please see replacement parts for these items. ASTM Grout Flow Cone Set, 0.5" (13mm)HC-2834S Grout Flow Cone Set, 0.75" (19mm)HC-2835S Ship wt. 30lbs. (13.6kg) Grout Flow Cone ASTM C939 Cast-aluminum flow cone with either 0.5" (13mm) or 0.75" (19mm) replaceable orifice. Includes adjustable point gauge assembly. Overall dimen- sions: 8" dia. x 12"H (203 x 305mm). H-2835 does NOT comply with ASTM C939. ASTM Grout Flow Cone, 0.5" (13mm)H-2834 Grout Flow Cone, 0.75" (19mm)H-2835 Ship wt. 10lbs. (4.5kg) Grout Flow Cone, Plastic Plastic flow cone with either 0.5" (13mm) or 0.75" (19mm) replaceable orifice. Includes adjustable point gauge assembly. H-2834 sold separately. ASTM Grout Flow Cone, 0.5" (13mm)H-2834P Grout Flow Cone, 0.75" (19mm)H-2835P Adjustable Point Gauge AssemblyH-2834P.7 Ship wt. 2lbs. (0.9kg) Grout Flow Orifice, Replacement ASTM C939 Grout flow orifice with either 0.5" (13mm) or 0.75" (19mm) opening. Grout Flow Orifice, 0.5" (13mm)H-2834.500 Grout Flow Orifice, 0.75" (19mm)H-2834.750 Ship wt. 1lb. (0.45kg) Grout Flow Cone Stand Sturdy well-constructed steel stand to support flow cones so the top is level and the cone free from vibration. Overall dimensions: 21"W x 9.5"D x 23"H. Grout Flow Cone StandH-2833 Ship wt. 9.5lbs. (4.3kg) Beaker, 6-liter Stainless Steel 6-liter stainless steel beaker with rolled-top edge, perfect for grout flow testing. Cleans up with ease. Beaker, 6-liter Stainless SteelH-2834SSB Ship wt. 2.8lbs. (1.27kg) Micrometer Bridge Set Designed to hold one cylinder to permit repeated volume change measurements without moving or disturbing the specimen. Includes the follow- ing items: H-2901 micrometer bridge, H-2902 micrometer depth gauge, H-2904 tapered cylin- der mold, H-2905.2 tamping rod, H-2905.2 glass plate and H-2905.3 weight. Micrometer Bridge SetH-2903 Ship wt. 23.4lbs. (10.6kg) Tapered Cylinder Mold ASTM C1090 Used to determine volume change of grout, mold is constructed of steel tubing 0.25" wall x 3" dia. x 6"H (6 x 76 x 152mm). Mold is split longitudinally with two quick-acting clamps welded to the mold. Top edge of mold is machine tapered to a narrow rim. Includes detachable base plate. Tapered Cylinder MoldH-2904 Ship wt. 7.8lbs. (3.5kg) Micrometer Depth Gauge Graduations in the thousandths of an inch (.001"), range 0 to 3", .125" rod dia. Sleeve is designed with staggered lines, hardened and precision ground screw; lock nut holds the setting at the precise measurement. Includes protective case. Base length is 2.5". Micrometer Depth GaugeH-2902 Ship wt. 2lbs. (.9kg) Micrometer Bridge Bridge is used to hold the H-2904 mold in place while repeated volume change measurements are made. Stainless Steel. Micrometer BridgeH-2901 Ship wt. 7lbs. (3.1kg) Tamping Rod ASTM C157, C192 Round, straight steel rod is .375" (10mm) dia. x 12" (305mm) long. Both ends are rounded to a hemispherical tip of the same diameter as the rod. Tamping RodH-2905.1 Ship wt. 4.5lbs. (2.04kg) Glass Plate Glass plate used with micrometer bridge setup. Glass PlateH-2905.2 Ship wt. 0.4lbs. (0.18kg) Weight, 3 lb 3 lb weight for use with micrometer bridge setup. Weight, 3 lbH-2905.3 Ship wt. 3lbs. (1.4kg) H-2905.3 H-2905.1 H-2903 (set) H-2901 H-2905.2 H-2902www.humboldtmfg.com • 1.800.544.7220 • 708.468.6300 244 CEMENT Flow H-3624F H-3622 H-3622M H-4144.8 Flow Molds Cast-bronze 2.75" top dia. x 4" bottom dia. x 2" high cone mold or cast-bronze 70mm top dia. x 100mm bottom x 50mm high. cone mold. Flow Mold, 2.75" / 4"x 2" highH-3622 Flow Mold, 70mm/100mm x 50mm highH-3622M Ship wt. 2.4lbs. (1.08kg) Pedestal Form Wooden form used to create a concrete base for flow tables. Pedestal FormH-3624F Ship wt. 28lbs. (12.7kg) Counter, Automatic Can be used to upgrade H-3625 motorized flow table so a predetermined number of drops can be set to run automatically. Use H-3614B.4F with H-3625.5F. Counter, Automatic, 120V 60HzH-3614B Counter, Automatic, 220v 50HzH-3614B.4F Ship wt. 4lbs. (1.8kg) Caliper, Mortar Diameter Check ASTM C87, C185, C230; AASHTO M152, T71, T137 Rugged caliper used to measure mortar flow diameter and indicate the + percentage of flow. Caliper, Mortar Diameter CheckH-3621 Ship wt. 2lb. (0.9kg) Mortar Flow Shield ASTM C230; AASHTO M152 Circular shield for use with H-3622 flow mold to prevent mortar from spilling on table top. Mortar Flow ShieldH-3623 Ship wt. 2lbs. (0.9kg) Straight Edge ASTM C185, D558, D559, D560, D698; AASHTO T137 Straight edge of ground steel with beveled edge. .125" x 1.25" x 8" (3 x 32 x 200mm). Straight EdgeH-4144.8 Ship wt. 0.9lbs. (0.9kg) Grout Boxes ASTM C1019 Cardboard box designed to be used to mold grout test samples. Each box forms 4 molds and can be used as a transport/shipping container as well. Boxes yield consistent, identical prism samples, while the engineered, slotted corrugation retains moisture while closely simulating CMU absorption rates. 25 boxes to a package. Overall dimensions: 7.5" x 7.5" x 7" (190 x 190 x 178mm). Section: 3.25" x 3.25" x 6.75" (83 x 83 x 171mm) Grout Boxes (package of 25) H-2838 Ship wt. 17.3lbs. (7.84kg) Grout Paper ASTM C1019 The grout paper is cut to dimensions of 7 1/2″ x 12″ and scored in three places to allow the paper to be folded into a 3″ x 3″ x 7.5″ prism. The grout paper molds are then placed into a cavity created by properly arranging concrete masonry units (CMU) and/or bricks to the same dimensions. The grout is then placed and consolidated into the cavity lined by the Humboldt grout paper. Not only is this method more economical than the corrugated cardboard boxes which are com- monly used, it also meets the guidelines of ASTM C-1019: for a thin, permeable material to prevent bond. In addition, the permeable grout papers are rigid enough to help prevent casting irregular shaped specimens which the use of thinner mate- rials can possibly yield. Using our grout papers to create compressive strength specimens in accor- dance with procedures outlined in ASTM C1019 will eliminate the need to make comparison sam- ples if proposing to employ alternative methods of creating test samples as noted in the standard.” Even if you are making 4 specimens like the corru- gated cardboard boxes, Humboldt Grout paper is less expensive per specimen. Grout Paper (package of 100) H-2836 Grout Paper (package of 500) H-2836.500 Grout Paper (package of 1000) H-2836.1M Ship wt. 5lb. (2.3kg) H-3621 H-2838 H-2836www.humboldtmfg.com • 1.800.544.7220 • 708.468.6300 CEMENT 245Compression/Flexural Combined Compression/Flexural Testing Machine ASTM C109, C348, C349; EN 196, 1015, 13813, 13892-3, 12504-1, 993-5, ISO 679, DIN 1164, 1048-1 BS 3892, 4550, 4551 Extremely stiff, four-column load frame tensioned without any play Measurement accuracy class 1 according to DIN EN 7500-1 in the specified mea- suring range. The testing machine combination is a space-saving unit consisting of compression and flexural testing machine which is suitable for compressive and bending strength tests of gyp- sum, mortar and cement samples, as well as light and aerated concrete. In the basic configuration, the framework is designed for force-controlled tests, whereby the force value is determined via strain gauges. Optionally a position measuring system can be installed on the compression or bending side. The massive steel frame is extremely stiff. The hydrau- lic cylinders are made from solid material. The end position is detected by an inductive sensor. The compression side is enclosed by four columns. The bending side is designed as an open C-frame. On both side is a simple insertion of different test fix- ture, inserts and devices possible. •Solid and stiff 4-column frame •Large test chamber protection made of trans- parent polycarbonate • Long piston stroke of 60mm with optimized test chamber height of 210mm for a wide range of applications •Force value detection via precise force trans- ducers (DMS based) •Various fixed test inserts or devices can be adapt into a machine to test according a large number of standards (ASTM / EN / BS etc.) •DOLI EDCi Control electronics fully-automatic test procedures suitable for force, displacement or deformation controlled tests with predefined loading speeds •Automatic break detection and free adjustable test end conditions •Readout and export of measurement data Safety The test frame with a control cabinet fulfills all requirements according to DIN EN ISO 7500- 1. The complete machine is delivered with an EC declaration of conformity and an operating Instructions according to the Machinery Directive 2006/42 / EG. A large area of the testing machine is equipped with an impact-resistant, transpar- ent test room protection made of polycarbonate. The position of the protective door is monitored by an inductive sensor. When the door is open, the hydraulic unit is depressurized. Control cabinet Control cabinet with main switch incl. under-volt- age release and emergency stop switch, as well as a “Schuko” plug on the front panel. Hydraulic system The powerful hydraulic unit with 20L oil tank incl. all necessary safety, control and directional valves according to DIN 4413. It generates a maximum system pressure of 350 bar and a volume flow of 1.2L / min. A fine 3µm pressure filter in the pres- sure line is filtering the hydraulic oil and protecting the system components. Incl. filter pollution, oil level and temperature switch(70°C). The hydraulic unit is inside of the control cabinet and is thereby particularly low noise < 66 dB (A). A high-quality servo valve for pressure or volume flow control enables the most precise force and position con- trol (closed-loop control). Measuring and control electronics As universal digital measuring and control elec- tronics for testing machines, a Doli EDCi20 con- troller is used. It is installed in the control cabinet and can optionally be operated with a remote control. The control electronics enables a fully automatic test execution with given load speeds for force-controlled tests (position and strain con- trolled tests optional).With sensitive and adjust- able break detection, the failure of the sample is detected early. Communication to the PC: Eth- ernet socket / USB 2.0 Remote maintenance via TeamViewer function(PC required). Technical data EDCi20 • Expansion option: 3 iSI modules (2 onboard) • System cycle: max. 2.5 kHz • Supply voltage: + 24 VDC, 1.5 A • Control output: ± 10 V A / B pulse train to control the subsequent elec- tronics Automatic sensor detection by intelligent sensor connector SGS. Calibration data is saved in the sensor plugs. PC required, but not supplied. All platens and accessories sold separately. Combined Compression/Flexural Testing Machine, 300kN/15kN – 230V 50/60HzHC-2821B.4F Ship wt. 880 lbs. (400kg) Combined Compression/Flexural Testing Machine, 400kN/30kN – 230V 50/60HzHC-2822A.4F Ship wt. 992 lbs. (450kg) Combined Compression/Flexural Testing Machines HC-2821B.4F HC-2822A.4F Capacity Compression 67,442 lbf. (300kN)89,923 lbf. (400 kN) Force measuring range, class 1 674 - 67442 lbf. (3 -300kN) 899 - 89,923 lbf. (4 - 400 kN) Column spacing front 11" (280mm)11" (280mm) Capacity Flexural 3,372 lbf. (15 kN)6,744 lbf. (30kN) Force measuring range, class 1 33 - 3372 lbf (0.15 - 15kN) 67 - 6744 lbf. (0.3 - 30kN) Stroke 2.3" (60mm)2.3" (60mm) Machine platens dimension Ø6.5" (165mm)Ø8.46" (215mm) Dimensions 47.25" x 22.45" x 76.77" (1200 x 570 x 1950mm) 47.25" x 22.45" x 76.77" (1200 x 570 x 1950mm) HC-2821B.4F HC-2822A.4F Shown with PC, not included HC-2820A.6 HC-2820A.4 HC-2820A.7 HC-2820A.5 Accessories for HC-2821B 4F & HC-2822A 4F see page 204 ACCESSORIESwww.humboldtmfg.com • 1.800.544.7220 • 708.468.6300 246 CEMENT Organic Impurities, Calorimeter H-3493A H-3492A H-3490A H-3491 Organic Impurities Test Set ASTM C40; AASHTO T21 Determines presence of injurious organic com- pounds in sands used in cement mortar or con- crete. Test serves as warning that further tests of sands are necessary before they can be approved for use. Air shipments must meet Dangerous Goods requirements because of Sodium Hydrox- ide Beads. Order H-3493X without Sodium Hydroxide Beads to avoid Dangerous Goods requirements. Organic Impurities Test SetH-3493A Test Set, w/o Sodium HydroxideH-3493AX Ship wt. 6.8lbs. (3kg) Graduated Bottle 12 oz. (.35L) graduated bottle for organics impu- rities test. Graduated BottleH-3490A Ship wt. 0.8lbs. (0.3kg) Organic Color Wheel ASTM C40; AASHTO T21 Color comparison wheel for use with organic impurities test. Color wheel has five different color filters to compare to test solution. Organic Color WheelH-3492A Ship wt. 0.6lbs. (.27kg) Sodium Hydroxide Beads 1lb (454g) Container of Sodium Hydroxide Beads. Air shipments must meet Dangerous Goods requirements. Sodium Hydroxide BeadsH-3491 Ship wt. 1.5lbs. (.68kg) Reaction Container ASTM C289 For determining potential alkali reactivity of aggregates (chemical method) when used with high alkali cements. Stainless steel unit is 2" dia. x 2.25" high (51mm dia. x 57mm) fitted with air- tight cover. 50-75ML capacity. Reaction ContainerH-3320 Ship wt. 1.3 lbs. (0.56kg) Cement Calorimeter, Digital ASTM C186 Features precision digital thermometer for deter- mining heat of hydration of cements by measuring difference between heat of solution of dry cement and heat of solution of a separate sample partially hydrated for 7 to 28 days. Constant-speed stirrer maintains uniform temperature throughout liq- uid and supplies sufficient agitation to keep solid reactant suspended in the acid mixture. Includes insulated wood case, insulated 1G (3.8L) can; 1 pt. (0.47L) vacuum jar with stopper; 2-channel, Precision Digital Thermometer with a resolution of 0.001°C; plastic funnel; stirring paddle and chuck; geared synchronous motor. Cement Calorimeter, Digital, 120V 60HzH-3161 Cement Calorimeter, Digital, 230V 50/60HzH-3161.4F Ship wt. 35lbs. (15.8kg) Calorimeter EN 196-9 Used to measure the heat of hydration of cement by the semi-automatic Langavant method. Test calorimeter includes factory calibration certificate. Temperature recorder provides (4) input chan- nels (1x Reference and max. 3x test Calorimeter) for recording and transmission of temperature values. Analysis software provides reporting and editing function for calculating the heat of hydra- tion. Unit includes: test calorimeter; reference cal- orimeter; mortar-sample container, temperature recording device and analysis software. Power for unit is supplied by USB from a PC or laptop. Does not include required PC. CalorimeterH-3162.5F Ship wt. 37lbs. (17kg) Bleed Stability of Cementitous Grout Kit ASTM C1741 Humboldt’s H-3601 Bleed Stability Grout Kit is used to evaluate the bleed stability of a fresh- ly-mixed grout under static pressure. It can be used in the field as a quality control test or in the laboratory to qualify grout materials. When using this test method, contract documents should ref- erence the number of required tests, as well as the test pressure and acceptance criteria desired for the testing procedure. The H-3601 Kit Includes: •Filtration Funnel, 47mm (includes viton o-rings and stainless steel 45 µm (No. 325) screen) •A/E Glass Fiber Filter, 47mm •Graduated Glass Cylinder, 10ml •Base and Support Rod •Clamp, Large Swivel Jaw, Coated •Clamp Holder (up to 3/4"/19mm) A pressure supply with gauge, pressure regula- tor, valve and metal drip wick (paper clip) are also needed, but are not provided. Bleed Stability of Cementious Grout KitH-3601 Ship wt. 8lbs. (3.6kg) H-3320 H-3161 H-3162.5F H-3601www.humboldtmfg.com • 1.800.544.7220 • 708.468.6300 CEMENT 247Gilmore, Water Retention, Bleeding H-3630A H-1763A H-3150 Cement Bleeding Apparatus ASTM C243 Used to determine bleeding rate and bleeding capacity of cement paste and mortar by direct and continuous procedure. Includes noncorrosive metal container for paste or mortar, collecting ring, support stand and necessary glassware. Rub- ber-covered double V-jaw burette clamp holds stopcock in position; single rubber-covered jaw clamp supports the burette and funnel assembly. Cement Bleeding ApparatusH-3600 Ship wt. 16lbs. (7.2kg) Water Retention Apparatus ASTM C1506, C110, C207 and E149 The apparatus is used in specification tests of masonry cement and physical testing of quick- lime and hydrated lime. These tests include: ASTM D1506, ASTM C110 and ASTM C207. This test method provides a means for determining the ability of mortars and plasters to retain water under suction. Test results may be used to deter- mine compliance with specifications. The results obtained using this test method can be used to compare the relative ability of mortars and plas- ters to retain water under suction. Unlike older models, this unit incorporates a vacuum regula- tor and gauge system in place of the old mercury manometer and relief column. The complete unit consists of an aspirator pump, vacuum regulator, vacuum gauge, three-way stopcock, flask, rubber gasket, brass funnel, perforated brass dish, filter paper and hardwood stand. Water Retention ApparatusH-3630A Ship wt. 25lbs. (11.3kg) Gillmore Apparatus ASTM C91, C141, C150, C266, C414; AASHTO T154 Used to determine initial and final set times of Portland cement, masonry cement, hydraulic hydrated lime and certain mortars. Comprised of two stainless steel needles with 0.0375" (4.8mm) cylindrical flat-end needles. One is 1/12" (2.12mm) dia. 1/4 lb. (113.4g) weight for initial set. The second is 1/24" (1.06mm) dia., 1lb. (453.6g) weight for final set. Gillmore ApparatusH-3150 Ship wt. 5.7lbs. (2.5kg) H-3600 DescriptionModel Strike-off plate, 0.5" thickness H-3154 Needle, 1/24" (1.06mm) dia. with 1lb (453.6g) weight H-3151 Needle, 1/12" (2.12mm) dia. with 1/4lb. (113.4g) weight H-3152 Gillmore needle, 0.050" dia. H-3152.4 Gillmore Accessories and Replacement Parts Water Retention Apparatus Replacement Parts DescriptionModel Funnel H-3630.3 Stopcock H-3630.4 Rubber gasket H-3630.18 Filter paper, 15cm, package of 100 H-3630.21 Perforated brass dish H-3631 Flask, 1000ml H-4913.1M Vacuum Pump H-1763A Drierite Air Drying Unit H-1759 H-3631H-3630.3 H-3630.4 H-3630.21 H-3630.18 H-3152.4 H-3154 H-3151 H-3152Next >